FC8308 VID = 1111 PID = 2222 Repair Fake Flash Drive Solution
Posted by inspectortech on October 4, 2009
FixFakeFlash – solution FC8308 controller identified with VID = 1111 PID = 2222, fake flash drive. The drive tested and repaired was from eBay Fake Flash Seller 123456wowo123456 aka mememao9898. Advertised as 16GB, it’s true capacity was 4GB. This fake flash drive can be repaired using the following information.
WiseOne repaired:
If you have this controller and or VID PID information, the solution may help you to repair your fake.
HOW I SUCCESSFULLY REPAIRED THE DRIVE (3.8Gb Capacity) By WiseOne
VID: 1111
PID: 2222
Controller: FC8308 – ALCOR
Chip: (one NAND flash chip SpecTek FBNL63A51K3WG-AF equiv. to Micron MT29F4G08MAA).
The data sheet (http://www.spectek.com/pdfs/SpecTek_pns_Flash.pdf) showed me the ID of the chip, and I found it in the FC MpTool INI file and discovered it was the same as the Micron chip (must be imported by
Micron as one of theirs).
Have repaired the flash device now with FC MPTool:
- Ran the FC MPtool.exe without the drive plugged in, plugged in the drive and clicked refresh.
- Choose the Micron MT29F4G08MAA, under Flash Type and under “Other” Tab, “Compel Flash”
- MP Setup: Optimize: LLF Set optimize
- Set VID and PID to 1111 and 2222 under “Information” tab.
- Chose filesystem FAT32 under “Bad Block” tab.
- Clicked Ok, then “Start”
It tested successfully with h2testw.
Note: You may consider to open the usb flash memory drive to check the storage chip before proceeding with the reflashing exercise, if the tool does not auto detect your memory flash storage chip.
Solution Provider: WiseOne. 20091003
Reported In at: SOSFakeFlashDrive@gmail.com
FixFakeFlash Inspectortech 
Vodka7up said
Can’t run the application, an error appears with the message “NO LOADER IMAGE FILE!”
fake_usb_victim said
The MPTools also gave me NO LOADER IMAGE FILE!” error.
Fernando said
ESTOU POSTANDO PARA DIZE QUE ESTOU CONSEGUINDO RECUPERAR MEU PEN DRIVER.
ELE RECONHECIA APENAS 8MB SENDO QUE ELE É DE 8GB, COM ESSE PROGRAMA ESTOU BATALHANDO E JA FIZ ELE RECONHECER 2GB E CONTINUAREI TENTANDO. MAS FUNCIONA PARABENS QUANDO EU CONSEGUIR COMPLETO EU DIREI A VOCES. UM ABRAÇO E OBRIGADO
Meins321 said
reupload:
http://rapidshare.com/files/285280298/FC_MpTool_1.19.rar
akash said
i installed the software mp tool it does not allow to access the refresh option , only password option is available ..plz help
akash said
sorry i mean only setup option is available
InspectorTech said
Where did you get the tool from? What version is it? Advise you look for a different one.
The objective is to find the version that recognizes the usb flash drive, and only check the set up options to make sure ecc is closed, then run in automode to repair the size.
There are many different versions, Akash. Many different tools.
jomar said
hey can you tell me the password for the set up buttom,, my flash drive is down to 62mb from 2 gig after formating
Jon said
Thanks, it worked. i bought my “16GB” usb on ebay and it turn out to be a 4GB after fix.
marcio said
Hi,I have a kingston 16gb, but he dont works, so i use the chipgenius and I discovery that the chip is an alcor fc8308 and the vid 518F, pid=6387. I try but did´not found any tool to repair, if someone have any sugestion I thanks.
Fred said
mptool on win 7 64bit does not find any drives.
Any ideas?
I open the program as administrator,.
The only pushable button is the setup one.
Asks for a pass change. Leaving all empty i can change the setup but still no devices found.
So the Start pause and so on are gray and unpushable.
Tried the ver 1.9 to 4.0; no luck.
Jose Roberto said
Eu não consigo entrar no programa. Preciso do password.
alguem teria para me enviar para o meu e-mal?
Jose Roberto said
hey can you tell me the password for the set up buttom, my flash drive is 128GB. Please send me by my e-mail.
thanks a lot
Silva said
Eu preciso da password para abrir o fc mptool
Alguem poderia me enviar por e-mail: jrsilvarc@terra.com.br
kamran aslam said
new download link
http://rapidshare.com/files/285280298/FC_MpTool_1.19.rar
FC_MpTool_1.19
Ran the FC MPtool.exe without the drive plugged in, plugged in the drive and clicked refresh.
Choose the Micron MT29F4G08MAA, under Flash Type and under “Other” Tab, “Compel Flash”
MP Setup: Optimize: LLF Set optimize
Set VID and PID to 1111 and 2222 under “Information” tab.
Chose filesystem FAT32 under “Bad Block” tab.
Clicked Ok, then “Start”
It tested successfully with h2testw.
Illidian Shadowhunter said
i got a advance flash drive which i bought as an 8gb flash drive…
chi[p genius shows it an alcor fc8308
vid 0011
pid 7788
but when i open it up it say’s the black controller chip reads fc8908
so i got the fc8908 tool formatted the flash it got detected as 4gb but started acting weird so i decided to flash it again but know it shows this error in the mp tool
30400: unknown flash error
ID[0]: 0x45,0xD7,0xD8,0xC2,0x76,0xD5
ps i cannot see the flash chip on the usb drive as it got erased….
so how can i fix this
thanks in advance for any help
andy said
can you tell me the password for FC Mptool?
Saad Mohamed said
pls help me
this Description
Protocal Version: USB 2.00
Current Speed: High Speed
Max Current: 100mA
USB Device ID: VID = 1111 PID = 2222
Serial Number: C4EABE42
Device Vendor: Generic
Device Name: Mass Storage
Device Revision: 0102
Manufacturer: Generic
Product Model: Flash Disk
Product Revision: 8.00
Chip Vendor: Alcor Micro
Chip Part-Number: AU6983/AU6986 – F/W EF5F